Each Pro Mount is precision-made, fitted with 3M™ Primer 94 and 3M™ VHB™ 4991F. For the best hold and long-term reliability, follow the steps below.

Step 1 — Test fit

• Position the mount on the helmet before removing the liner.
  
• Ensure it sits flush with the chin area.
  
• Attach your camera briefly to check angle and level.
  

Note: Don’t peel the adhesive liner in this step, use product page as reference.

Step 2 — Clean the surface

• Use the included alcohol wipes to remove dust, grease and wax.
  
• Let the area fully dry.
  

Step 3 — Warm the surfaces

• Peel back the red liner.
  
• Gently warm both the adhesive pad and helmet surface with a hair dryer for 5–10 seconds (warm, not hot).
  
• Light heating helps activate VHB for maximum bond.
  

Step 4 — Apply & press

• Align carefully and apply the mount.
  
• Press firmly and evenly across the whole surface for 60 seconds.
  
• If a small edge lifts, re-warm lightly and press again until flush.
  

Step 5 — Cure time

• Allow to cure 24 hours before use.
  
• If you didn’t apply heat, allow 72 hours.
  
• Do not attach the camera during the cure period.
  

Step 6 — Safety Tether

• Clean, dry and lightly warm the spot on the helmet.
  
• Apply the tether base, then loop the cord through the camera housing or thumbscrew.
  

Step 7 — Final check

• After curing, attach your camera and test over a soft surface.
  
• Confirm the mount feels solid and edges are fully seated.
  
  

Need help?

Questions about fitment or installation? info@promounts.uk — we’ll be happy to help.

Safety notice: Always ensure the mount and camera are securely attached before use. Pro Mounts UK cannot accept responsibility for loss, injury or damage resulting from incorrect installation, misuse, unsuitable mounting surfaces, or failure to check the mount before use.

Each Pro Mount Flexy Mount is designed to conform to a wide range of surfaces while providing a strong, secure adhesive bond. For the best hold and long-term reliability, follow the steps below.

Step 1 — Test fit

• Position the Flexy Mount on the surface before removing the adhesive liner.
• Gently form the mount to match the shape and curvature of the surface.
• Check your desired camera position and angle before installation.

Note: Do not remove the adhesive liner until you are happy with the position.

Step 2 — Clean the surface

• Use the included alcohol wipe to remove dust, grease, wax and other contaminants.
• Allow the surface to fully dry before installation.

Step 3 — Apply the mount

• Remove the adhesive backing, taking care not to touch the adhesive surface.
• Carefully position the Flexy Mount and press it into place.
• Ensure the mount follows the surface closely with no significant gaps or lifted areas.

Step 4 — Apply pressure

• Press firmly and evenly across the entire mount for at least 30 seconds.
• Pay particular attention to the edges and curved areas to ensure the adhesive has made full contact with the surface.

Step 5 — Cure time

• Allow the adhesive to cure for at least 24 hours before use, or 72 hours if you didn't heat the mount.
• Do not attach a camera or place load on the mount during the cure period.

Important — One-time adhesive

The adhesive pad is designed for one-time application only.

Do not remove and attempt to reposition or reapply the mount once it has been bonded to a surface. Removing the mount can compromise the adhesive and it should not be relied upon for subsequent use.

Step 7 — Safety Tether

• Clean, dry and lightly warm the spot on the surface.
  
• Apply the tether base, then loop the cord through the camera housing or thumbscrew.

Step 6 — Final check

• After the curing period, check that the entire mount is firmly bonded and that no edges have lifted.
• Attach your camera and test the mount over a soft surface before use.
• Check the mount and adhesive regularly, particularly before high-speed or high-impact activities.

Need help?

Questions about installation or suitability? info@promounts.uk — we’ll be happy to help.

Safety notice: Always ensure the mount and camera are securely attached before use. Pro Mounts UK cannot accept responsibility for loss, injury or damage resulting from incorrect installation, misuse, unsuitable mounting surfaces, or failure to check the mount before use.

Your Pro Mount replacement adhesive kit allows you to prepare and reapply your mount using fresh 3M™ VHB™ tape and Adhesive Promoter Primer. For the best hold and long-term reliability, follow the steps below.

Step 1 — Remove the old adhesive

• Gently warm the existing adhesive using a hair dryer to soften the bond.
• Carefully peel the old adhesive away from the mount.
• Avoid using excessive heat or sharp tools that could damage the mount.

Step 2 — Clean the mount

• Thoroughly clean the adhesive surface of the mount using the included alcohol wipes, ensuring all traces of the old adhesive and primer are removed.
• The surface should be clean, dry and free from grease or residue before continuing.

Step 3 — Apply the primer

• Using the included Adhesive Promoter Primer wipe, apply a thin, even coat to the area of the mount that will contact the adhesive.
• Allow the first coat to fully dry.

Note: Apply the primer to the mount only, not the helmet surface.

Step 4 — Allow the primer to dry

• Do not apply the tape while the primer is still wet.

Step 5 — Apply the new VHB tape

• Carefully align the supplied 3M™ VHB™ tape with the mount.
• Apply the tape without touching the adhesive surface unnecessarily.
• Press firmly and evenly for 60 seconds, ensuring the entire pad has made good contact with the mount.
• Then carefully cut off the excess tape from the mount.

Step 6 — Install the mount

Once the replacement adhesive has been fitted, the mount can be installed onto your helmet following the normal Pro Mount installation procedure.

• Test-fit the mount before removing the outer adhesive liner.
• Clean and fully dry the helmet surface.
• Gently warm the adhesive and helmet surface before application.
• Position carefully and press firmly and evenly for 60 seconds.

Step 7 — Cure time

• Allow the adhesive to cure for at least 24 hours before use.
• If installed without gently warming the surfaces, allow 72 hours.
• Do not attach your camera during the curing period.

Step 8 — Final check

• Once cured, check that the mount is firmly bonded and all edges are fully seated.
• Attach your camera and test the installation over a soft surface before use.
• Always use your safety tether when riding.

Need help?

Questions about replacing your adhesive or reinstalling your mount? info@promounts.uk — we’ll be happy to help.

Important: Replacement adhesive is intended for one application only. Once the mount has been installed, do not remove and attempt to reapply the same adhesive.